we can not make the parameter const because API.

Backport of 2cfb561e and 1a406e3f

Conflicts:
	bin/varnishtest/vmods.h
	configure.ac
	lib/Makefile.am

backport of f820f801

Conflicts:
	include/tbl/params.h

Only RST frames received earlier than this duration will be considered
rapid.

Includes backports of the following upstream doc-touchups:
- 151f4d50
- 46d4f823

Conflicts:
	include/tbl/params.h

Conflicts:
	bin/varnishd/VSC_main.vsc
	include/tbl/sess_close.h

This adds parameters h2_rapid_reset_limit and h2_rapid_reset_period,
which govern the rate of which we permit clients to reset streams.

If the limit is exceeded the connection is closed.

Related to: #1851

Conflicts:
	include/tbl/params.h

This should make the code easier to read and stop us from being inconsistent.
Signed-off-by: Asad Sajjad Ahmed <asadsa@varnish-software.com>

The error check is not performed in a critical section to avoid
contention, at the risk of not seeing the error until the next
transport poll.

Conflicts:
	bin/varnishd/http2/cache_http2_session.c

Once a client is reportedly gone, processing its VCL task(s) is just a
waste of resources. The execution of client-facing VCL is intercepted
and an artificial return(fail) is returned in that scenario.

Thanks to the introduction of the universal return(fail) proper error
handling and resource tear down is already in place, which makes this
change safe modulus unknown bugs. This adds a circuit breaker anywhere
in the client state machine where there is VCL execution.

A new Reset time stamp is logged to convey when a task does not complete
because the client is gone. This is a good complement to the walk away
feature and its original circuit breaker for the waiting list, but this
has not been integrated yet.

While the request is technically failed, it won't increase the vcl_fail
counter, and a new req_reset counter is incremented. This new behavior
is guarded by a new vcl_req_reset feature flag, enabled by default.

Refs #3835
Refs 61a15cbf
Refs e5efc2c8
Refs ba54dc91
Refs 6f50a00f
Refs b8816994

Conflicts:
	bin/varnishd/cache/cache_vrt_vcl.c
	bin/varnishd/cache/cache_vcl_vrt.c
	bin/varnishd/mgt/mgt_param_bits.c
	include/tbl/params.h

The goal is for top-level transports to report whether the client is
still present or not.

It was particularly hard to follow once we reach client c3.

Not sure why 6fbb9377 does not originate
from trunk.

We don't need a delay, we need to sync operations.

This parameter allows the user to choose which storage backend / stevedore
that the H/2 receive buffers are allocated from. By default it uses
Transient.

Conflicts:
	bin/varnishd/mgt/mgt.h
	bin/varnishd/mgt/mgt_param.h
	bin/varnishd/mgt/mgt_param_tbl.c
	include/tbl/params.h

This was found lacking in our H2 implementation. Previously we would have
included any padding bytes in the request body. Possibly it would have
caused errors if there also was a C-L present, or more likely just corrupt
request bodies.

If the client sends nothing but padding bytes and ends up consuming the
entire stream window with no actual request bytes buffered, the request
thread side of things would not send any stream window updates. Handle
this corner case by sending a window update from the session thread.

According to the spec the padding is an 8-bit field, and fields should be
treated as unsigned unless otherwise specified, which it is not for any of
the padding related places. Allow varnishtest to generate padding up to
255 bytes long.

This is the test case that fails if these changes aren't in tree. Note the
commented out rxwinup commands that are necessary for the proper fail mode
when run without the varnishtest window update changes.

With the new request body data handling, Varnish changes behaviour
significantly wrt to stream window updates sent to the client. Window
updates will only be sent once the data is consumed by the client through
the request body VFP handling. Test cases that rely on receiving a window
update to sync the H/2 stream needs to be adopted.

This makes it easier to not have to know exactly when and how many window
updates to expect in a test case.

We have a strict min at the protocol default here. This is because we
don't have the 'use settings only after peer ack' in place yet. If the
value is lower than the protocol default, the very first stream could get
a flow control error.

H2 streams waiting for request body data will timeout after timeout_idle
seconds if no new data on the stream is being received. This will ensure
that individual H2 streams can be reaped if there is no data received from
the peer.

This implements stream data handling using a buffer between the H/2
session thread and each stream thread. This is needed to avoid head of
line blocking on the session socket when a data frame is received for a
stream thread that is not yet ready to receive it.

The buffer used will have to be as large as the send window the peer
expects at the time the stream is opened. This will typically be 65535
unless the h2_initial_window_size parameter has been changed.

Stream window updates will then be issued only once data is removed from
the buffer by the request body being consumed from the request handling
thread, limited in size to what space is then available in the buffer.

Conflicts:
	bin/varnishd/http2/cache_http2_proto.c

The H/2 session thread does have a VSL buffer already set up, but the
'wrk->vsl' pointer was not set. This caused issue for e.g. LRU_NukeOne()
as it wants to log. Set the buffer for the duration that the worker is
dedicated as an H/2 session thread.

And use that for logging purposes when a successfully opened h2 session
ends. RX_JUNK is still the default session close reason when existing
reasons aren't accurate enough.

Fixes #3393

In the same fashion as include/tbl/params.h for legibility.